Drawing List Cross Reference

REPORT ACA 3877 PRODUCTION GROUP DRAWING LIST
OF THE MODEL K, SEPTEMBER, 1940
(Last Updated 12/22/08)

Important Web Note:

The information contained within this web page was reproduced from a hardcopy of the following report: "Report ACA 3877 Production Group Drawing List of the Model K September, 1940". Every effort was made to re-type this report accurately, but I make no statement of accuracy of the original report or the reproduction of this report on this web site. This information is for unofficial use only. Additional information may be added to this web page to aid in locating and understanding these drawings.

Attention:

Mr. John Houser has supplied this web site with The Production Drawing List Of The Model K to help you when you write to him requesting a drawing you may need when restoring your Aeronca K. If you need a drawing you must send a letter to John, along with the 1) Drawing Number, 2) Title and 3) Latest Change, just as they appear on the list below. Naturally, there has to be a charge for this service depending on drawing size and number of drawings. You can write Mr. John Houser at 1615 Sunset St. Middletown, OH. 45042

INDEX
Control System Group	Fuel System Group	Tail Surface Group
Engine and Oil Group	Fuselage Group	Three View Assembly Group
Fixed Equipment Group	Landing Gear Group	Wings, Ailerons and Struts
Note: Due to discontinuance of production on the subject model, this group of drawling list shows the last applicable change letter for each drawing.

* denotes drawings sent to Civil Aeronautics Authority.

Control System Group
Number	Title	Latest Change
*1-14	Bearings - Control S. - Rudder Pedal Center	A
1-28	Assembly - Aileron Sprocket and Shaft	A
*1-44	Horn - Elevator	D
*1-48	Bushing - Control Post	A
*1-50	Bushing - Control Post Mount - Rubber	A
*1-51	Washer - Control Post Mounting	A
*1-59	Horn - Control Column	A
*1-60	Support - Control Column - Pulley
*1-62	Bearing - Control Column	B
*1-63	Horn - Rudder Pedal	B
*1-64	Collar - Control Column - Bearing	A
*1-65	Gusset - Control Column
1-66	Gusset - Control Column Aileron Sprocket
*1-76	Shaft - Control Wheel (Obs. Superseded by 1-349)	F
*1-77	Pedal - Control System Rudder - Pass.	B
*1-79	Joint - Control Column Aileron Universal (Obs.)	B
*1-100 through 1-179	Tubes - Standard SAE 1025
*1-184	Washer - 4130 Blank - Flat
1-196	Spring - Rudder Pedal
*1-211	Fitting - Aileron Wire	C
*1-212	Clamp - Control Shaft	A
*1-213	Chain - Aileron Control
*1-214	Sprocket - Aileron Control Chain	A
*1-227	Shaft - Control Column - Torque	B
1-240	Bearing - Control Column - Ball
1-243	Handle - Tab Regulator (N.D.)
1-244	Pin - Tab Regulator Handle (N.D.)
1-245	Plate - Tab Regulator Escutcheon (N.D)
1-325	Washer - Tab Control Handle - Fiber
*1-349	Shaft - Control Wheel	B
*1-403	Regulator - Tab	D
*1-405	Fairlead - Tab Control Cable	A
1-408	Turnbuckle - Tab Control Wire (N.D.)
*1-411	Fairlead - Table Control Cable - Center	A
1-502	Stud - Tab Regulator	B
1-629	Clamp - Bowden Cable (1/4)	A
1-658	Clamp - Bowden Cable (3/8)	A

*2-22	Cable - Wing Aileron	A
*2-23	Cable - Rudder	A
*2-25	Cable - Aileron Loop	A
*2-27	Cable - Fuselage - Elevator	C
*2-73	Cable - Tab Control	C
*2-113	Universal - Control Column	A

*3-5	Assembly - Right - Rudder Pedal	F
*3-6	Assembly - Left - Rudder Pedal	E
*3-10	Wheel - Control	C
3-12	Board - Tab Regulator Mounting	B

*7-3	Installation - Control System	F
*7-5	Assembly - Control Column	C

*8744	Plate - Adjustment Rudder Pedals

Engine and Oil System Group
Number	Title	Latest Change
1-46	Clamp - Standard 1/4 inch Tube	B
1-195	Clamp - Round Tube
1-256	Bracket - Throttle	D
1-261	Washer - Engine Mount - Bottom
1-262	Washer - Engine Mount - Top
1-263	Clamp - Tachometer Shaft - Special
1-265	Washer - 1-1/2 O.D. x 1/2 I.D. #1025 (N.D.)
1-322	Bushing - Motor Mount
1-350	Block - Stewart Warner Instrument Shim
1-360	Line - Oil Pressure Gauge	A

2-43	Control - Engine Throttle	D

*7-7	Installation - Engine and Oil System	D

5116	Washers and Bushings - Engine Mount Upper Bracket

Fixed Equipment Group
Number	Title	Latest Change
*1-78	Pedal - Brake (Optional Equipment)	F
*1-217	Support Seat - Front	B
*1-223	Support - Fixed Equipment - Seat Back
*1-231	Clamp - Battery Board - Pipe (Optional Equipment)
1-258	Rod - Battery Box - Tie (Optional Equipment)	C
1-260	Plate - Navigation Lights (Optional Equipment)
1-266	Strap - Lid - Battery Box (Optional Equipment)
1-273	Plate - Door Lock - Scuff	B
1-277	Strip - Baggage Compartment Support	A
1-293	Plate - Sta. 4U Fus. Fairing Support (Op. Equipment)
1-326	Guide - Aileron Cable	A
1-329	Thermometer Bulb - S. W. Oil Temperature Gauge
1-350	Block - Stewart Warner Instrument - Shim
1-351	Switch Plate - Ignition
1-649	Mast Aerial (Optional Equipment)

2-3	Extinguisher - 1 Pint Fire (N.D.)
2-28	Guard - Control Wires	C
2-29	Cushion - Seat Block (N.D.)
2-30	Cushion - Seat Bottom (N.D.)
*2-34	Board - 6-V Exide Battery (Optional Equipment)	C
2-35	Bracket - Compass (Optional Equipment)	B
2-66	Handle - Door
2-71	Cable - Brake (Optional)	A
2-80	Handle - Inside Door

3-9	Belt - Two Place - Safety
3-14	Board - Fixed Equipment - Floor	B
*3-17	Box - Exide 3AC Battery (Optional Equipment)	D
3-26	Bracket - Compass Mounting - Special (Op. Equip)
3-29	Instrument - Oil Temperature, Oil Pressure and Tachometer - Aeronca

*4-7	Panel - Instrument (Obsolete)	C
*4-8	Equipment - Fixed	D
*4-11	Installation - Battery - 6-V Exide (Op. Equipment)	B
*4-19	Panel - Stewart Warner Instrument	J
4-34	Compartment - Baggage (N.D.)
*4-102	Installation - RCA Radio (Optional Equipment)	C

5-8	Circuit - Position Light Wiring

5626	Eyebolt - Brake Pedal (Optional)
8170	Washer - Drag Wire (Optional Equipment)

Fuel System Group
Number	Title	Latest Change
*1-100 through 1-179	Tubes - Standard SAE 1025 (Optional Equipment)
1-195	Clamp - Round Tube (Optional Equipment)
*1-199	Flange - Gas Tank Outlet	A
*1-215	Strap - Gas Tank	A
*1-226	Street Ell - Gas Tank Outlet	A
*1-228	Strap - Auxiliary Gas Tank (Optional Equipment)
*1-230	Support - Auxiliary Gas Tank (Optional Equipment)
1-234	Cap - Auxiliary Gas Tank (Optional Equipment)
1-251	Lines - Copper Fuel	A
1-252	Line - Gas
1-253	Bracket - Fuel Strainer
1-254	Handle - Fuel System Shut-Off Valve	B
*1-274	Support - Aux. Gas Tank - Board (Op. Equipment)	A
1-278	Brace - Wobble Pump (Optional Equipment)
*1-279	Clamp - Auxiliary Gas Tank - Board (Op. Equip.)	B
*1-280	Clamp - Auxiliary Gas Tank Strap (Op. Equipment)
1-281	Bracket - Auxiliary Gas Tank (Optional Equipment)
*1-304	Cap - Gas Tank	D
*1-305	Screen - Fuel Tank Finger
1-380	Assembly - Gas Tank Cap and Gauge	A
1-388	Rod - Float - Gas Tank
*1-507	Rod - Oil Tank Strap	A
1-616	Fitting - Oil Tank Filler Neck (Op. Equipment)
1-822	Cap - Fuel Tank

2-32	Pad - Gas Tank	D
2-33	Board - Gas Tank - Front
*2-36	Bracket - Aux. Gas Tank - Wobble Pump (Op. Equip)	B

*3-18	Board - Aux. Gas Tank - Support (Op. Equipment)	A

*4-6	Installation - Fuel System	D
*4-9	Tank - Auxiliary Gas (Optional Equipment)	D

*7-12	Tank - Gas Main	B
*7-16	Installation - Auxiliary Gas Tank (Op. Equip)	E

5172	Float - Gas Tank
5174	Filler Neck - Gas Tank	A
5324	Strainer - Gas

Fuselage Group
Number	Title	Latest Change
*1-1	Lug - Fuselage Station 3U - Hinge Point	A
*1-2	Lug - Fuselage Station 3U - Hinge Point	A
*1-3	Fittings - Fuselage Station 4U - Hinge Point
*1-5	Lug - Fuselage - Wing Strut - Station 3L - Front	B
*1-6	Lug - Fuselage - Wing Strut - Station 3L - Rear	C
*1-7	Fitting - Landing Gear Station 2L - Saddle - Fuselage
*1-8	Gusset - Fuselage Station 2L - Landing Gear Fitting
*1-11	Support - Fuselage - Rudder Pedal Bearing	B
*1-17	Lug - Fuselage - Tail Skid
*1-23	Lug - Fuselage Station 3L - Landing Gear	A
*1-41	Socket - Fuselage Station 3L - Seat Beam
*1-42	Fitting - Fuselage - Seat Back
*1-45	Bracket - Fuselage - Pulley	C
1-46	Clamp - Standard - 1/4 inch Tube	B
*1-49	Bracket - Fuselage 2U control post mounting (Obs.)	A
*1-52	Layout - Fuselage Rudder Stops	A
1-54	Bushing - Fuselage Throttle Control
*1-89	Assembly - Fuselage Station 2L - Landing Gear Fitting
*1-100 through 1-179	Tubes - Standard SAE 1025
*1-184	Washer - 4130 Blank - Flat
1-192	Hinge - Standard 2 inch door
1-195	Clamp - Round Tube
1-197	Clip - Cowling - Boeing Type
1-198	Patch - Covering Square
*1-210	Fitting - Fuselage Station 4L (Seaplane only)	C
*1-216	Lug - Lower Engine Mount Fitting	A
*1-222	Lug - Fuselage Engine Mount - Upper	A
*1-225	Fitting - Lower Engine Mount	A
1-235	Plate - Fuselage Fitting Station 3L - Gusset
*1-236	Gusset - Fuselage Truss - Station 3U-3U'
*1-237	Bracket - Fuselage Tube #13 - Pulley
1-238	Bracket - Fuselage Tube #42 - Pulley
1-239	Collar - Fuselage - Tail Post
*1-241	Bracket - Fuselage Tube #41 - Pulley	B
*1-242	Plate - Fuselage - Pulley Bracket
*1-250	Gusset - Fuselage - Station 3L
1-257	Frame - Wing - Inspection Window
1-268	Patch - Covering Round	A
1-270	Window - Inspection
1-293	Plate - Fuselage Station 4U - Fairing Support
1-298	Support - Stringer - #1 Top and #4 Bottom
1-299	Support - #2 Top Stringer
1-300	Support - #3 Top Stringer
1-301	Support - #1 Bottom Stringer
1-302	Support - #2 Bottom Stringer
1-303	Support - #3 Bottom Stringer
1-364	Gusset - Fuselage Station 4U
1-365	Bracket - Nose Cowl Fairing Bow
1-366	Fairing Bow - Windshield - Lower
1-367	Socket - Fuselage Fairing Strip
1-368	Support - Nose Cowl - Lower Fairing Bow
*1-529	Lug - Control Pulley	A
*1-532	Fitting - Station 4U Seaplane Float (Seaplane only)
*1-533	Gusset - Seaplane Float Fitting (Seaplane only)

*2-1	Truss - Station 3U-4U - Fuselage	B
*2-11	Fitting - Fuselage Station 3L - Strut and L.G.	C
*2-12	Skeleton - Fuselage Fin	B
*2-14	Bushings - Fuselage Stabilizer Brace Wires (Obs.)	A
*2-42	Bracket - Fuselage Station 2U - Control Post Mount	B
2-51	Fairing Bow - Landing Cowl - Upper
2-52	Fairing Bow - Nose Cowl - Upper Front
2-53	Fairing Bow - Nose Cowl - Side Horizontal
2-54	Fairing Bow - Nose Cowl - Upper Rear
2-55	Fairing Bow - Nose Cowl - Bottom Rear
2-56	Fairing Bow - Nose Cowl - Lower Front
2-57	Fairing Bow - Nose Cowl - Side Rear

*3-3	Mounting - Fuselage Control Post Bearing (Obs.)
3-20	Skeleton Door
3-21	Assembly - Top Cabin Fairing
3-22	Block - Cabin Fairing Corner	A
3-23	Bulkhead - #1 Side Fairing
3-24	Bulkhead - #6 Side Fairing

4-12	Installation - Door (N.D.)
4-13	Bulkhead - #2 Side Fairing
4-14	Bulkhead - #3 Side Fairing
4-15	Bulkhead - #4 Side Fairing
4-16	Bulkhead - #5 Side Fairing
4-20	Mounting - Fuselage Control Post Bearings	B

5-9	Bulkhead - Fuselage Top Fairing	C
5-10	Bulkhead - Fuselage Top Center	D

*7-2	Skeleton - Fuselage	I
*7-9	Fuselage - Cowl and Cover	A
*7-13	Installation - Firewall
7-21	Assembly - Nose Cowl Fairing Bows	A

*5340	Bearing - Rudder Torque Tube	B
5733	Fairing - Clip
*8318	Lug - Stabilizer Tie Rod Anchor - Fuselage	A
*8332	Anchor Fitting - Fin Tail Post - Fuselage
*8333	Bracket - Rudder and Elevator Pulley - Fuselage	D
8338	Clamp - Bowden Casing - Tab Control - Fuselage	B
9005	Fastener - Cowling (N.D.)

Landing Gear Group
Number	Title	Latest Change
*1-26	Plate - Landing Gear - Tail Skid Shackle
*1-61	Sleeve - Tail Skid - Rubber Bushings (Obsolete)
*1-69	Sleeve - Strut - Tail Skid
*1-72	Bushing - Tail Skid	A
*1-80	Lug - Tail Skid Shoe (Obsolete)
*1-81	Gland - Oleo Landing Gear - Packing	C
*1-82	Piston - Oleo - Landing Gear	C
*1-83	Show - Tail Skid (Obsolete)
*1-84	Pin - Oleo - Landing Gear - Retainer
*1-85	Sleeve - Oleo - Landing Gear	A
*1-86	Arm - Tail Skid	A
*1-91	Fitting - Landing Gear - Frame (Obsolete)	B
*1-92	Fitting - Landing Gear Linkage Lower (Obsolete)	A
*1-93	Retainer - Landing Gear Oleo - Spring	C
*1-94	Fitting - Landing Gear - Frame	C
*1-96	Spring - Oleo - Landing Gear
*1-97	Tie Rod - Oleo - Landing Gear
*1-98	Assembly - Oleo - Landing Gear Piston Rod
*1-99	Assembly - Shoe and Lug Tail Skid (Obsolete)
*100 through 1-179	Tubes - Standard SAE 1025
*1-184	Washer - 4130 Blank - Flat
1-194	Boss - Landing Gear Oil Plug (N.D.)
*1-200	Assembly - Oleo L. G. Female Scissors Link (Obs.)	C
*1-201	Assembly - Oleo L. G. Male Scissors Link (Obs.)	D
*1-202	Gusset - Scissors Link Oleo Landing Gear	A
*1-203	Plate - Female Scissor Link - Back (Obsolete)	B
*1-204	Plate - Male Scissor Link - Back (Obsolete)	B
*1-205	Flange - Scissor Links - Oleo Landing Gear (Obs.)	B
*1-206	Plate - Axle Stub - Torque	A
*1-207	Gland - Oleo Landing Gear Packing	C
*1-208	Pin - Oleo Landing Gear - Dowel	B
*1-209	Bushing - Landing Gear Scissors Link (Obsolete)	A
1-218	Plate - Landing Gear Frame
*1-224	Bushing - Oleo Piston Rod - Upper	A
1-271	Washer - Tail Skid
1-272	Support - Brake Arm - Pulley (Optional Equipment)	A
1-327	Fitting - Standard - Straight Drive - Alemite
*1-341	Fitting - Landing Gear Scissors Oleo Leg	A
*1-342	Fitting - Landing Gear Scissors Frame	A
*1-344	Link - Oleo Scissors - Male	A
*1-345	Link - Landing Gear Frame Scissor - Female	A
*1-346	Bushing - Landing Gear Scissor Link	A
1-355	Arm - Tail Wheel (Optional Equipment)
1-356	Washer - Tail Wheel (Optional Equipment)
1-358	Bolt - Tail Wheel (Optional Equipment)
*1-369	Spring - Tail Wheel - Control (Optional Equip.)
*1-467	Washer - 1025 Blank - Flat
1-522	Support - Goodyear Wheel Pants - Outer (Optional)
1-523	Reinforcement - Wheel Pants - Outer (Opt. Equip)
1-595	Gusset - Landing Gear Scissors Frame Fitting

2-4	Assembly - Goodyear Disk Brake (Op. Equipment)	C
*2-17	Strut - Tail Skid	A
*2-26	Axle - Oleo Landing Gear	A
2-46	Cable - Brake (Optional Equipment)
2-47	Skid - Tail Wheel (Optional Equipment)
2-48	Yoke - Tail Wheel (Optional Equipment)
2-49	Arm - Tail Wheel Control (Optional Equipment)
2-107	Support - Wheel Pants Inner (Goodyear) (Opt. Equip.)
2-110	Reinforcement - Goodyear - Wheel Pants - Inner (Op. Eq.)
2-111	Plate - Goodyear Wheel Pants - Baffle (Opt. Equip.)

*3-7	Assembly - Tail Skid	C
*3-8	Assembly - Oleo Landing Gear - Strut	F
*3-13	Installation - Landing Gear	C
*3-25	Shoe - Tail Skid	A

*4-26	Assembly - Tail Wheel (Optional Equipment)	B
*4-42	Installation - Ski (Optional Equipment)	A
*4-43	Installation - Ski (Optional Equipment)
*4-62	Installation - Tail Wheel Model H-2 (Op. Equip.)	A

*6-2	Frame - Landing Gear	I

*7-6	Assembly - Landing Gear	D
7-41	Blank - Wheel Pants (Optional Equipment)
7-48	Assembly - Wheel Pants - Goodyear (Opt. Equipment)

*5442	Tail Skid Compression Spring	B
8655	Clip - Brake Lever (Optional Equipment)	A
8656	Pulley - For Brake Operation Cable (Opt. Equip.)	A

Tail Surface Group
Number	Title	Latest Change
*1-37	Fitting - Tail Surface - Elevator - Spar End	A
1-90	Clip - Tail Surface - Elevator Tab - Spring Clip
*1-100 through 1-179	Tubes - Standard SAE 1025
*1-220	Horn - Elevator Tab	B
*1-221	Rod - Tab Operating (Obsolete)	B
*1-284	Tube - Tail Installation Shuttle (Obsolete)	A
1-372	Patch - Rudder Horn	A
1-466	Rod - Tail Surface - Tie	B
*1-467	Washer - 1025 Blank - Flat
*1-495	Rod - Tab Operating	A

*2-31	Assembly - Elevator Tab	E

*3-19	Fin - Seaplane Auxiliary (Seaplane Only)
3-32	Covering - Stabilizer
3-33	Covering - Rudder
3-34	Covering - Right Elevator
3-35	Covering - Left Elevator

*4-2	Skeleton - Stabilizer	B
*4-3	Skeleton - Left Elevator	G
*4-4	Skeleton - Right Elevator	C

*7-10	Installation - Tail Surfaces	E

8505	Nut - Sleeve - Elevator Horn
8506	Stud - Elevator Horn	B
8507	Hinge Pins - Control Surfaces	A
*8508	Fitting - Flying White to Stabilizer	A
8511	Hinge Tube - Stabilizer and Rudder	B
8521	Plate - Torque - Elevator
*8541	Bracket - Tab Control	A
*8542	Slide - Elevator Tab Control	A
*8543	Spring - Elevator Tab - Slide
*8545	Clamp - Bowden Casing
*8551	Cable Assembly - Tab Control - Revised Tail Surfaces	B
*8560	Rudder Assembly	B
*8561	Horn - Rudder

Three View Assembly Group
Number	Title	Latest Change
*7-4	Three View Landplane	A
*7-14	Three View Seaplane (Seaplane only)	B

Wings, Ailerons and Struts
Number	Title	Latest Change
*1-4	Bracket - Wing - Aileron Hinge Support
*1-9	Gusset - Wing Rib - Rear Spar
*1-10	Gusset - Wing Rib - Front Spar
1-12	Nose - Wing Panel Rib	A
*1-13	Fitting - Wing - Drag Strut End
*1-15	Blank - Wing - Drag Bracing
*1-16	Fitting - Wing - Jury Strut	C
1-18	Gussets - Rib - Tip Section - Spar
1-19	Gussets - Rib - Tip Section
1-20	Nose - Wing - Tip Rib
*1-21	Assembly - Wing - Aileron - End Rib and Hinge	B
*1-22	Strut - Wing Drag System - Compression
*1-24	Nose - Aileron Rib
*1-25	Hinge - Aileron - End
*1-27	Fitting - Aileron Hinge Tube Front Spar	A
*1-29	Bracket - Wing - Aileron Pulley
*1-30	Hinge - Aileron - Center Female	A
*1-31	Tube - Wing Tip -Drag	B
1-32	Brace - Wing - Trailing Edge - Aileron Bay - Kick	A
*1-33	Section - Wing Strut Outer - Extruded
*1-34	Section - Wing Strut Inner - Extruded
1-35	Gusset - Aileron - Center Rib
*1-36	Arm - Aileron Pulley Bracket
*1-38	Fitting - Wing Aileron Hinge Tube - Rear Spar	A
*1-39	Fitting - Wing - Rear Strut - Upper End	A
*1-40	Fitting - Wing - Rear Strut - Lower End	B
*1-43	Hinge - Wing - Aileron - Center Male
*1-53	End - Wing - Rear Strut Adjustment
*1-56	Bushing - Wing Front Strut Fitting - Upper End	B
*1-57	Fitting - Wing Front Strut - Upper End	A
*1-58	Fitting - Wing Front Strut - Lower End	A
*1-67	Fitting - Wing - Front Spar - Butt End	B
*1-68	Fitting - Wing - Rear Spar - Butt End	B
1-70	Section - Wing - Aileron Bay - Upper	B
1-71	Section - Wing - Aileron Bay - Lower	B
1-73	Guard - Aileron Control Cable Pulley	E
1-74	Gusset - Wing Rib - Rear Spar	A
1-75	Gusset - Wing Rib - Front Spar	A
*1-95	Fitting - Wing - Drag Bracing
*1-100 through 1-179	Tubes - Standard SAE 1025
*1-180	Section - Standard Trailing Edge
*1-181	Section - Standard Quarter Round
*1-182	Section - "T" - Standard
*1-183	Rod - 10 x 32 Standard - Tie	A
*1-184	Washer - 4130 Blank - Flat
*1-185	Stringer - Standard - Square Spruce
*1-188	Bushing - Standard - Micarta 1/2 x 1/4	E
*1-189	Bushing - Standard - Micarta 5/8 x 3/8	D
*1-190	Fitting - Standard - Tie Rod
*1-191	Bushing - Standard - 3/8 x 1/4	E
1-193	Bushing - Oilite 3/8 O.D. x 1/4 I.D. (N. D.)
1-198	Patch - Covering - Square
1-219	Bushing - End Aileron Hinge
*1-247	Clamp - Front Strut to Jury	C
*1-248	Clamp - Rear Strut to Jury	C
1-257	Frame - Wing - Inspection Window
1-268	Patch - Covering - Round	A
1-270	Window - Inspection
1-291	Corner - Block - Fairing Strip Support
1-292	Support - Fairing Strip	A
1-387	Patch - Aileron Hinge
1-464	Lug - Jury Strut Clamp

*2-2	Blank - Aileron - Rib
*2-5	Fitting - Wing - Front Spar to Strut	E
*2-6	Fitting - Wing - Rear Spar to Strut	E
*2-7	Channel - Wing Strut Fitting	D
*2-8	Fitting - Wings - Spars to Struts	B
2-9	Rib - Aileron
*2-10	Horn - Aileron	A
*2-13	Rib - Aileron - Trailing Edge
*2-15	Strut - Wing Brace Rear	D
*2-16	Fitting - Wing Front Strut Lower Outer	C
*2-21	Cable - Wing Aileron Balance	A
*2-22	Cable - Wing Aileron	A
2-50	Rib - Root Rib Nose	B

*3-1	Rib - Wing Stations 8 and 15 Trailing Edge	C
*3-2	Assembly - Aileron Horn
*3-4	Strut - Wing Brace Front	C
*3-11	Strut - Jury	D
3-16	Rib - Wing Station 1 - Trailing Edge	A

*4-1	Bow - Wing Tip
*4-5	Strut - Wing - Front Brace - Temporary	A
4-10	Covering - Wing	A

*5-1	Rib - Wing Panel Main
*5-2	Rib - Wing Panel Aileron	A
*5-3	Rib - Wing Panel Root	E
5-4	Rib - Wing Tip Section	A
*5-5	Assembly - Wing - Aileron
*5-6	Support - Wing Aileron Outer Hinge	C
*5-7	Rib - Wing - Stations 9 and 10

*7-1	Assembly - Wing	E
*7-11	Installation - Wings and Struts	C
*7-15	Spars - Wing - Front and Rear	B

5388	Gusset - Rib - Rectangular
5389	Gusset - Rib - Triangular
5390	Gusset - Rib - Trailing Edge
5400	Rib - Standard
8232	Bearing - Tie Rod Fitting - Wing	A